AMD Announces Development of DTX Form Factor
Anh Tuan Huynh
January 10, 2007 12:00 AM
comment(s) - last by
AMD's David Schwarzbach holding a DTX PCB panel
AMD works on new small form factor standard
AMD today announced the company is developing a new small form factor standard. The new form factor, dubbed DTX, is AMD’s attempt to unify the various proprietary small form factors currently in use. DTX will be an open industry standard available to all case, motherboard and system manufacturers, but will not be limited to AMD-based products.
There will be two DTX standards available -- DTX and mini-DTX. The current DTX specification will only define a few requirements, the primary of which are motherboard mounting points and keep-out areas. Alternative specifications, like Micro-BTX, have strict guidelines for everything from airflow regulation to legacy I/O definitions.
AMD claims the consumer market needs a small form factor standard for the following reasons:
Electricity cost savings
Take up less space for both practical and aesthetic purposes
Enables systems that are quiet
Do not generate excessive heat
The enterprise clients need a small form factor for the following reasons:
Lower energy bills to help reduce operating costs
Enables differentiated and competitive solutions
Smaller, sleeker form factors take up less space in offices and cubicles and are designed to operate quietly
DTX falls between the current Micro-ATX and Mini-ITX standards. DTX motherboards will measure in at 200mm by 244mm compared to the 170mm by 170mm footprint of Mini-ITX motherboards. MicroATX motherboards measure 244mm by 244mm.
Mini-DTX will initially target sub-6 liter enclosures and support processors with TDPs up to 35 watts. The footprint of Mini-DTX motherboards will be 200mm x 170mm -- just a tad wider than Mini-ITX motherboards.
While there are already plenty of other standards on the market such as ATX, Mini-ITX and BTX, AMD’s goal with DTX is greater flexibility and lower costs. Greater flexibility is achieved by making DTX motherboards backwards-compatible with ATX and Micro-ATX. Lower costs will be addressed with DTX due to the clever sizing of DTX motherboards. Most manufacturers are able to produce two standard ATX motherboard PCBs per PCB panel, a manufacturer can now cut four DTX or six Mini-DTX motherboards from the same panel.
There will be room for two expansion slots on DTX motherboards. No constraints have been set for the expansion slot configuration, which leaves manufacturers to decide which slots are needed. An ExpressCard expansion slot is also planned for the DTX form factor.
Expect AMD to release the final DTX specification later this quarter. It is unknown when or if manufacturers will produce systems and components based around the DTX standard, but several motherboard and enclosure manufacturers have already announced DTX products will appear in their 2007 roadmaps.
This article is over a month old, voting and posting comments is disabled
RE: I hate Intel
1/10/2007 3:02:00 PM
Simple, Intel already tried a new case standard called BTX which failed misserably. Now AMD is trying to do it the right way by opening it to everyone and making it backwards compatible with ATX. This way prodution of DTX motherboards can start and you can still put them in any ATX case. You can even update your current mobo in if you have and ATX and possibly a MicroATX case. That is one of the aspects where BTX failed. Needed new case and new motherboard.
RE: I hate Intel
1/10/2007 5:08:57 PM
did BTX fail? That will be shocking news to the OEMs that use it for almost all of their systems. Dell uses it for a large percentage, and Gateway uses it for 95%+. I'm not sure about HPaq, but it wouldn't surprise me if they use it too.
Just because something isn't used commonly in the enthusiast market doesn't make it a failure.
There are also BTX motherboards for AM2; Dell uses them.
RE: I hate Intel
1/12/2007 12:25:37 PM
Let's just say that Intel has backed off on BTX. Last I saw, Intel themselves really cut back on their BTX board offerings. Maybe the major OEMs are using BTX because ATX boards are still popular, making it harder to use third party components to repair their computers. This would not surprise me.
"We are going to continue to work with them to make sure they understand the reality of the Internet. A lot of these people don't have Ph.Ds, and they don't have a degree in computer science." -- RIM co-CEO Michael Lazaridis
ZOTAC Announces Diminutive ZBOX PI320 pico
August 27, 2014, 9:00 AM
Quick Note: QNAP Announces $129 QGenie 7-in-1 NAS for Mobile Users
July 14, 2014, 9:32 AM
Apple Launches 21.5” iMac with 1.4GHz Core i5 Processor Priced at $1,099
June 18, 2014, 8:07 AM
Lowe's "Holoroom" Brings Holodeck, Home Improvement Dreams Closer to Reality
June 13, 2014, 9:06 AM
Intel to Broaden Market for Fanless Tablets, Ultrabooks with 14nm Intel Core M
June 3, 2014, 10:42 AM
ZOTAC Announces Four New Silent ZBOX Mini-PCs
June 2, 2014, 9:21 AM
Most Popular Articles
Microsoft's Surface 2 Tablet Family Gets a $100 Price Cut
August 25, 2014, 1:16 AM
Owner of "Decepticon" Maserati Ordered to Appear in Court This Thursday
August 25, 2014, 7:55 AM
LG Posts Teaser Video of Its “Round Face” G Watch R Smartwatch, Set for IFA Lauch
August 24, 2014, 2:49 PM
Windows 9: "Upgrade Now" Button Coming for Enterprise Updates, ARM Preview in H1 2015
August 26, 2014, 8:00 PM
Second ZMapp-Treated Patient Dies of Ebola, Supplies Run Out
August 25, 2014, 7:03 PM
Latest Blog Posts
Space Terrorism is a Looming Threat For the United States
Apr 23, 2014, 7:47 PM
Facebook Aims to Provide Internet to "Every Person in the World" with Drones, Satellites
Apr 1, 2014, 10:20 AM
Retail Mobile Sites Experience Outages in Light of Simplexity's Bankruptcy
Mar 14, 2014, 8:48 AM
Tesla vs. BMW: Who Has the Safer EV?
Feb 1, 2014, 2:56 PM
Justice Leaks Details of Next HTC One Two Flagship Phone
Dec 5, 2013, 4:04 PM
More Blog Posts
Copyright 2014 DailyTech LLC. -
Terms, Conditions & Privacy Information