backtop


Print 57 comment(s) - last by cybertrip.. on Jan 19 at 10:55 AM


AMD's David Schwarzbach holding a DTX PCB panel
AMD works on new small form factor standard

AMD today announced the company is developing a new small form factor standard. The new form factor, dubbed DTX, is AMD’s attempt to unify the various proprietary small form factors currently in use. DTX will be an open industry standard available to all case, motherboard and system manufacturers, but will not be limited to AMD-based products.

There will be two DTX standards available -- DTX and mini-DTX. The current DTX specification will only define a few requirements, the primary of which are motherboard mounting points and keep-out areas. Alternative specifications, like Micro-BTX, have strict guidelines for everything from airflow regulation to legacy I/O definitions.

AMD claims the consumer market needs a small form factor standard for the following reasons:
  • Electricity cost savings
  • Take up less space for both practical and aesthetic purposes
  • Enables systems that are quiet
  • Do not generate excessive heat
The enterprise clients need a small form factor for the following reasons:
  • Lower energy bills to help reduce operating costs
  • Enables differentiated and competitive solutions
  • Smaller, sleeker form factors take up less space in offices and cubicles and are designed to operate quietly
DTX falls between the current Micro-ATX and Mini-ITX standards. DTX motherboards will measure in at 200mm by 244mm compared to the 170mm by 170mm footprint of Mini-ITX motherboards. MicroATX motherboards measure 244mm by 244mm.

Mini-DTX will initially target sub-6 liter enclosures and support processors with TDPs up to 35 watts. The footprint of Mini-DTX motherboards will be 200mm x 170mm -- just a tad wider than Mini-ITX motherboards.

While there are already plenty of other standards on the market such as ATX, Mini-ITX and BTX, AMD’s goal with DTX is greater flexibility and lower costs. Greater flexibility is achieved by making DTX motherboards backwards-compatible with ATX and Micro-ATX.  Lower costs will be addressed with DTX due to the clever sizing of DTX motherboards. Most manufacturers are able to produce two standard ATX motherboard PCBs per PCB panel, a manufacturer can now cut four DTX or six Mini-DTX motherboards from the same panel.

There will be room for two expansion slots on DTX motherboards. No constraints have been set for the expansion slot configuration, which leaves manufacturers to decide which slots are needed. An ExpressCard expansion slot is also planned for the DTX form factor.

Expect AMD to release the final DTX specification later this quarter. It is unknown when or if manufacturers will produce systems and components based around the DTX standard, but several motherboard and enclosure manufacturers have already announced DTX products will appear in their 2007 roadmaps.


Comments     Threshold


This article is over a month old, voting and posting comments is disabled

RE: Pic
By justjc on 1/10/2007 9:13:16 AM , Rating: 4
What the man holds up is the plates they use in production today, for manufacturing ATX boards, which is why the plate naturally is bigger than ATX boards ;).

The smart thing about DTX and mini-DTX is that such a plate, as those used today, will, if devided into 4, be the correct size for 4 DTX boards, or if divided into 6, be the size of 6 mini-DTXs = No waste and no new machinery needed = cheaper, environmentally sound, boards.


RE: Pic
By marvdmartian on 1/10/2007 9:39:05 AM , Rating: 3
Don't worry, OP, I thought that too, at first. Had to click on the pic, and see that it was 4 mobos on one panel, to understand! :)

By my calculations, if the DTX is 200 x 244 mm, then a 4 board pcb will be 400 x 488 mm.....and if you can get 6 boards out of that same pcb, in the mini-dtx form, then those boards ought to be ~ 163 x 200 mm size, or ~ 6.5 x 8 inches in size, right? That puts them pretty close to the original size of Shuttle's SFF motherboards, which could make for some excellent computer mods! Now if they'll just keep the price reasonable, as pointed out by someone else here, and not make them atrociously priced, like the mini and nano itx!!

Oh yeah, and another thought......when someone comes up with the eventual ETx format, will it work okay with the one exception that every time you connect to the internet, it will try to.....phone home?? ;)


"If they're going to pirate somebody, we want it to be us rather than somebody else." -- Microsoft Business Group President Jeff Raikes











botimage
Copyright 2014 DailyTech LLC. - RSS Feed | Advertise | About Us | Ethics | FAQ | Terms, Conditions & Privacy Information | Kristopher Kubicki